PLUMBING 101: A NECESSITY FOR INSTALLING A BATHTUB

Plumbing 101: A Necessity for Installing a Bathtub

Plumbing 101: A Necessity for Installing a Bathtub

Blog Article

Instant Quote

Just how do you actually feel when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a bath tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old tub with a new one is also a reasonably challenging task. If the old bathtub is readily easily accessible, the project can relocate rapidly; if you have to open a wall surface to get rid of the old tub and also place the new bath tub, the task is much harder. In either situation, the project is within a house handyman's skills, although you will need an assistant to leave the old tub and also set in the brand-new one. Make sure you have qualified on your own for the task as well as are comfortable trying it. Instead of hiring a professional to take over a halfway-completed job, it is much better to think about employing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This write-up will certainly assist you set up a brand-new bathtub in your bathroom if you have already purchased a new tub as well as don't require to alter the plan of your previous water system pipelines.
Your tools as well as material checklist ought to consist of the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Installment


    To start with, the supporting framework provided with the bath should be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
    Fit the versatile tap ports to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you utilize all of the provided washing machines.
    Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its last placement.

    Removing Old Taps


    If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, activate the taps to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the restricted gain access to that is commonly the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
    Before moving on to fit the new faucets, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.

    Installing the Tub


    Making use of both wood boards under its feet, place the tub in the needed setting. The wood boards are handy in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four small points.
    The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub till the level checks out level.
    To mount taps, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
    Switch on the supply of water and also inspect all joints and also brand-new pipework for leakages and also tighten them if required. Load the bathtub as well as additionally examine the overflow electrical outlet and also the normal electrical outlet for leaks.
    Lastly, deal with the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the bathtub must wait until the tub has actually been utilized at the very least once as this will certainly resolve it into its final placement.

    Fitting New Taps


    If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the current supply pipes.
    If you require to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers are in location between the faucet and also the sink. Safeguard the faucet in position with the maker given backnut. Once the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former type must be linked to the faucet finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the area where the bathroom fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, creating the water to permeate the wall in between the bath as well as the tiling, leading to difficulties with moisture and also possible leakages to the ceiling below.
    You can pick from a range of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched paper or soft rope. Keep in mind to always load the bath tub with water before securing, to allow for the activity experienced when the tub is in use. The sealer can break rather early if you do not consider this activity prior to sealing.
    Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly available on the market. It is a good idea to fit the floor tiles using waterproof or waterproof glue and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    A Step-by-Step Guide to Installing a Bathtub

    I'm certainly very enthusiastic about Installing A Bathtub and I am hoping you enjoyed the new post. Liked our blog entry? Please share it. Help other people locate it. Many thanks for your time spent reading it.


    Solve now, call!

    Report this page